wondering

Hey all, ive got myself a little tec hsk600.. 2 stroker i believe 3hp, 4 cycle, no crank case. Wondering if i can do a carb swap on it???? Any clues???:confused::confused::confused::confused:

I have a 6.5hp motor piped and air cleaner and 12 tooth front and 60 back for sprockets and my clutch started messing up and was wondering whats the best clutch to get

On the old OldMiniBikes site a little black square appeared on the screen to let you know that you had a PM. I'm wondering if there is something comparable on the new site and I'm just overlooking it. Thanks guys, Ogy

This motor was given to me recently...just wondering if it's worth keeping and rebuilding/hopping up. I don't know much about these motors or whether or not there's an aftermarket for them. I was told that the rings were shot in this motor, but once I got it home I found that it's locked up...

Hi, im new here. ive been restoring old arctic cat sleds and some motorcycle projects and this weekend I found this and picked it up along with a Yamaha dt basket im going to restore. I was wondering what model it is and any help any of you can offer as to its worth, places to find parts ...

bought this and another mini bike last night just wondering what model it is

First shot at this so feel free to chime in. Not sure how resto or mod to go but there's a lot of room on this mini for engine so we'll see. It's a 5HP Tec on it now but I have others including a 6.5 Predator, and I'm wondering how big of an engine will fit since I'm an adult (in size and age...

Can this be done and will there be any performance gains in doing so. I just bought a 69727 ca. motor and was wondering if the swap was possible.

Looking for some help for my project does anybody make a bolt on 60T "flat" sprocket to use with a 6" Astro wheel. I'm wanting to use a 5.30/4.50-6 rear tire on a 6" Azusa Astro wheel with a 60T sprocket and I want to use the OldMiniBikes clutch brake so I was wondering if somebody knew of a sprocket...

Apparently this is a bonanza scout mb250 that I have, and the steering shaft in the forks seem to have a little wobble in them. Feels worn out, and will also slightly bind when turning. I was wondering, does the shaft have bushings or something that can be replaced?

Good day guys could use a little input if you could. I have found a 3 h.p Briggs and Stratton brand new in the box with tags on and all and am wondering if it's a good buy or not so counting on your experience to help decide. The only concern I have is the gear reduction device on the side...

Hey yall, new to this Forum. I am restoring an old Sherpa bike that has the two speed transmission and was wondering if anyone could tell me what kind of fluid I should put in it? The transmission that is

Hey guys a local kid has posted up these two mini's and Is wondering what are they ? Any help would be appreciated .:thumbsup:

We have 58 entries. Dang that is a lot of bikes! Entries now closed. There are two that messaged me earlier, so they may yet get added in for 60 total! 13 Vintage 21 Open 5 MTTW 3 Scratch 16 JFF Looking forward to all the building yet to come! And for those wondering, yes, I am...

It's on craigslist now I'm just wondering if it's worth a ten hour round trip.

http://www.oldminibikes.com/forum/general-minibike-talk/93600-warehouse-minibike-found.html I was just curious, what ever became of this or the opening poster. Hent had some of the last posts with some input but then it just faded away. The Thread starter just left every one hanging ,no up...

So during the Tare down when I was talking the forks off one of the springs got stuck in the framework and won't come out. And I don't want to mess anything up by doing something stupid. So I was wondering Has anyone ever had this problem? And how did they get it out?

A family member was recently diagnosed with it.Was just wondering if anyone on here has it.

Does anyone know the correct valve stem to guide clearance? Also has anyone removed the stock cast iron guides? If so how do you remove them. Wondering if they can be pressed out or if they are cast in and have to be machined out.

I'm running a Predator bone stock for now and I am wondering if anyone has found a way to adjust the governor to allow just a little more RPMs. Any ideas?