bushings

I have a Huskee Hill Climber made in Tiawan. I need new fork tube bushings. The need to fit in a 21/32" head tube and have a 1/2" diameter hole for the bolt. They are about an inch long and the flange is about one inch across.

Looking for the following parts - PN#165-030 and 165-031. I am told they are no longer available and OldMiniBikes is out of stock. If anyone has one or knows of some alternatives please let me know! -Ryan

Anyone know who sells steering bronze flange bearings for a Little Indian 400. It looks like the OD is 7/8in and the ID is 5/8in.I need these for a restoration project. Any help would be appreciated. I already checked OldMiniBikes and looked at Allied Leisure but can't find any in their listings(may have...

Some may know that I've been having a hard time like many of you fixing this problem. I just got back from the machine shop and after looking at my stuff they seem to think the most cost effective way is to make new plates to use a cheap aftermarket bearing and have a nice tight fit...

I am looking to purchase a set of LIL INDIAN bronze fork / bolt bushings. If you have some please let me know.

Always had 5/8" axles so bushings and spacers were never a problem. Going with Azusa wheel on my Roper project (stock front wheel too far gone) but has a 1/2 inch front axle and will need bushings. Suggestions, advice greatly appreciated. ( had a machine shop drill out 1/2" to 5/8th" axle hole...

Bag o' bolts I just bought has stainless steel fork neck bushings.... any idea of what year/models etc had bronze vs. stainless? :shrug:

Does anybody know where I can get steering neck bushings for a Taco22? I tried Some 5/8odby 1/2id and they wouldn't slide into the steering neck. The ones I have semm to be to big for the steering neck. Thanks

I need new bushings for the steer tube on my Boonie Bike. I've been all over the place and can't find a match. Anyone know of a good source? The book is really vague. It just says 5/8 x 1" bearings. It doesn't give the specific ID and OD.

I am after 2 x replacement Steering Bushings for my Deckson Daredevil :o See below for photos and dimensions (excuse me, we are metric over here, I think I got the conversions right) 8) Any help would be greatly appreciated!

OldMiniBikes.com has 3 different sizes. What size on the El Tigre? Thanks in advance for any help. Pic of bike in (what is it?) section. Thread title(bought for $100).

They are the last piece I need for a Hustler restoration, anyone have two Rupp fork bushings for a '71-'73 bike?

Need some shock eye bushing/ rubbers for my Super Bronc rear shocks. A suitable fix?

Anyone know where to get shock bushings that will work in old Taco shocks? HD

I'm in the process of building up my first mini I'm kind of a freak for details. the front end seems to have too much play in it for my likings. if i tighten up the bolt it don't steer, but if let loose it has way too much slop. the down tubes are not wallowed out, it is just a poor design...

Does any one know how to remove the lower portion of the fork on a 675? I pull the living hell out of it on my vice, hammer on it and it will not come out for anything, they must have been pressed in there really good. Its driving me nuts!! I need to replace the springs on my forks. Any...

I am having problems figuring out what is supposed to take out the loosness in the neck where the forks attatch to the frame. There is a grease fitting but you just can't tighten the bolt to prevent fork wobble, are there bearings or cups that prevent this like on a motorcycle? I will post...

I have not found a source for bronze fork fork/neck bushings! Anyone know a place that sells them? I have one set but need several more, I saw some split nylon ones but have never used them. Does anyone know about them also? Any help would be appreciated! Thanks.............

My sears (Bird) has some slop in forks ,any ideas or suggestions on bushings.The originals look like brass.

I'm thinking about making a mold and reproducing the Sebac shock bushings. Talking to a molding shop, I don't think it can be done for less than $10-12 for a set of 4 pieces. Any interest?