clone

I have a Powerfist 7hp and I just finished installing the billet flywheel and rod but I am just curious if removing the governor is optional? Like is it possible to rev the motor to say 5600rpm or will it actually restrict the rpm? I don't know if I am explaining this clearly enough but if you...

Can I just rub my head on hi grade sandpaper to flat for more compression and also what is the max lift that I can have when I DO THIS? Thanks

I have a Baja Warrior with a 196 clone. I was just going to repair the engine and slam it in the frame of this bike, but with how easy and cheap it is I somehow ended up with a shaved head, .036 jet(stock emulsion tube), aftermarket air filter, Modified rocker cover with PCV valve and breather...

Got a bar stool racer in a trade recently and this engine was on it. I had to swap out motors because this one was too much for that bar stool. Not exactly sure how much or what has been done to this engine, but it's scary fast. The guy I got it from said it has a Weisco piston with a fresh...

L shaped tank bracket. Think it was on hf and Titan clones.

does it exist? I know OldMiniBikes has som flathead parts, but no camshafts, which is what im buing for the flathead. and cam, rod, and springs for gx clone. Since i live in Norway id like to by parts from on place and save on shipping. Thanx. Einar-A

Starting to get all the parts together for my new build. Building a full open clone this time around and I will post as I make progress. Starting out with a 2.815 big bore/long rod combo from Clements. Got the block and side cover powder coated last night.

I have seen many people use their predator 212's on slanted engine mounts without adjusting the angle of the carb.. Not sure if I will need to but does anyone have any good examples of how to make a slanted adapter for a stock clone carb??

Running yellow clone. Local pickup. $50 Needs aftermarket air cleaner. Has new carb. Grandville Michigan.

I'am building a hemi predator with RTC 6 head , it's getting a dyno 308 cam . With this cam and rockers what would my lift be . I have no idea how to figure it out . Next ?? Will this be too much lift for this set up ? Next ?? I'am also building a red clone with a black mamba and champion...

Will these work in stock honda clone with bsp 2 cam and stock head? Thanks

so I bought a Honda head a little while back and between some conversation with my brother I have a bad feeling they sold me a clone head and not a Honda. not as if they ripped me off but like they miss understood me and sold me a clone head. I think the numbers on the casting are Z4M I could be...

Is there an adapter plate for a Briggs Raptor that will allow me to adjust it easily (similar to the one for the clone)?

Picked up a 550 series b&s that is missing the plastic air box. I have seen listed the k&n style filters for the hf predators and clone (honda gx I assume) Do the adapters listed on OldMiniBikes warehouse fit the briggs carb? Is there one available for briggs? Thanks in advance.

I've spent days reading and researching on what motor I have I still don't know for sure. I've came to the conclusion that I should just open it up and go from there. Specs I know about Engine : on a Baja warrior mb200 minibike. Dealer said its a rato r200 which indeed it is stamped...

FINALLY GOT A CHANCE TO WORK IN THE GARAGE TODAY AS THE TEMP HIT 52 DEGREES. HAD THE WHEELS SODA BLASTED AFTER CHRISTMAS, POLISHED THEM AND INSTALLED WITH NEW BEARINGS AND TIRES. RE-DID THE FENDERS AND PAINTED THEM METALLIC GOLD ALONG WITH THE CLONE TANK AND AIR CLEANER. READY FOR MOTOR INSTALL...

Im looking to go 420cc big block in my chopped and lowered Baja Warrior. I need a 420cc that can use the 390cc aftermarket cams and mod parts. From what i think i know, the predator and its copy's are a no go as the cam bearing bush is bigger so the 390 cams don't work. Im looking at the BE...

Has anyone painted their engine to match their bike? I have a predator to go on my trailblazer which I was considering painting to match my newly reupholstered seat. I would love to see any pics that anyone has. thanks

I recently built a clone with all the goodies , cam, springs,arc rod,flat top piston, anyway I ran the motor for like 20mins then I notice it was leaking oil out the side cover gasket. I removed motor from the bike and broke the engine down , I wanted to check torque on rod & switch cam &...

brand new hemi head with pushrods ready to bolt on - $50, $100 if you want it ported 5 bolt valve cover clone head, ported and milled - $50 king billet steel flywheel - $45 2 seks clone ceramic coated headers - $35 each super stock rlv clone header - $10 isky black mamba jr cam - $30 custom...