My predator 212 has so much crank end play that the flywheel fins are hitting the cover bolts. I want to replace the bearings. Does anyone know the size of bearings needed for a first generation non-hemi 212?
https://www.OldMiniBikes.com/Crank-Bearing-ID-_875-OD-_2_048-Width-_500.html
or...
Well I've never seen this before but, The Thread end of my HS40 crank snapped off !
Clean, like ya cut it with a knife!
Question is will a 3 or 3.5 Crank work as well OR is it a HS40 crank only thing?
This is a lighted HS40 as well if that matters.
Thanks
I have a 3.5 briggs 091202 / 0016 01 / 9503603 cover is not so great for clutch cover mounting... NO threaded holes?
Can it be switched out with one that will work for mounting clutch cover?
I'm a little green at this engine stuff. any info would be great Thanks
I have a 71 Tecumseh HS40. I broke the threaded end off of the crankshaft:hammer:....(my own dumb ass fault)....I gotta get a new one....Can anyone tell me the Tecumseh part #.
How do I find out what is the correct crank for my engine?
I have a HS40 with lighting coil engine that has the short output shaft. I need the crank that had the longer output shaft as used on Foxes and Rupps.
I'm tired of getting the wrong part, there must be a P/N for the correct one...
Got a honda gx200 block today and was thinking of putting predator hemi crank in it but need to know what billet rod i should use. Guy on fleabay sells the crank and flywheel as poor mans stroker for a gx200 but i had a hemi crank laying around and wanted to try this for myself. Has anyone else...
Tom and I took the kids out to play tonight ... Tom's grandson Elijah had driven Tom's 2-seater Manco Go Kart powered by Tom's motor of choice, the infamous 5hp Briggs the previous day for the 1st time.
My Granddaughter Rylee has spent many hours on mini bikes but never rode in a Kart before...
Hi all,
Ready to install my clutch on my rebuilt 5hp just to find that I can't. I do not have any threads in the end of the crank to put a bolt in. :censure:
Surely there's gotta be another way? Any help much appreciated.
I had to use this crank because of the parts shortage here in...
Hopefully this is a simple question. Im 90% finished rebuilding my 130000 series 5hp. I just realized my shaft 3/4" is about 1.25" long. I dont have enough to put a 2 sprocket clutch on it. Will a single sprocket work or do i need a longer crank shaft?
Hey guys I'm looking for a Briggs flathead 5hp I/C motor with a dual ball bearing crank and side cover. It doesn't have to be complete, as long as it has the stock air shroud, and most of the motor parts are there, head, sidecover, and crank.
COOL old briggs 5 hp, I believe its 5 hp and 1959
has good comp, but had a pump mounted on it so would need a diff crank, all complete, tank has small dent
sell all or any of it
50 plus ship
Hey all, ive got myself a little tec hsk600.. 2 stroker i believe 3hp, 4 cycle, no crank case. Wondering if i can do a carb swap on it???? Any clues???:confused::confused::confused::confused:
How do I change the oil seal on the side of the block where the crank sticks through? the bearing is good so id rather not mess with it, but the seal is bad. got a new one ready to go. the block is all tore down.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.