kill

I have two Squirrels with the Suicycle.. ALMOST a third the same day as the second one, like 10 miles apart.. But yesterday I got me a WOODCHUCK with the Roadster II :laugh: Or I could have... I DID kick him in the ass, and tell him GET OUT OF THE ROAD as I drove by though... :scooter: He...

Ok, so I have another dumb question. But thank God you guys are tolerant. I was going to wire up a new motor with the standard two wire toggle switch, but want to instead use the little single wire push button switch you can buy from Northern. So my question is this....if the Northern push...

I've never put a Kill Switch on any engine and can't seem to find a post for it. Can anyone tell me the best way to put one on a HF 6.5? KingPaul

Do you guys use a switch (as in "On" or "Off" toggle)? And if you do where can you purchase one. Im just not trusting my button.

how do i make a tecomseh hs40 kill switch ? it engine has a sparkplug ground out . not too safe for the kids in an emergency. can i connect a wire to the sparkplug ?

I just recently bought a Dunnecycle and I'm re-doing the whole thing. It's all there but I need 2 things: A complete decal set (including the decal on the gass tank) An original kill switch or similar replacement Anyone have any of these for sale?

comfort? Mini bike - $200 (Wayland) Date: 2010-04-22, 5:41PM EDT Reply to: sale-tvkun-1705274928@craigslist.org [Errors when replying to ads?] 70's mini bike with 3.5 HP Briggs & Stratton motor. Started right up after sitting 8 years in the basement but runs ruff, and needs a tune-up. Full...

OK, I just bought a Lil Indian w/ a 5hp Briggs & Straton on it. The guy who put it in didn't hook up the kill switch wire from his old engine. He said the wire used to go right to the spark plug, but when he put it there and used it, it shocked him so he pulled it. The current kill...

its just a normal 3.5 hp engine. can u show me some pics on how to hook it up? here is the engine im planning to connect it to,

My go kart has a Modified clone motor on it. The oil sensor is removed so unhooked the oil sensor box on the outside of the motor. Then i just have a straight connection from the thick black wire to the kill switch but it wont turn off. I need help. If this setup is wrong then i have no problem...

in ca, $25

in ca, $25

I installed a single wire kill switch and I am havig trouble with it.I made sure the handlebars were clean before mounting.Problem is it only works sometimes.Other times it just wont ground the engine even if you wiggle it.I was wondering if its because of the fork bearings.They have ball...

anyone tried this mod? I copied this response out of another thread- contributed by "altered 7151", but I didn't see any follow-ups to his suggestion..... want to know if anyone has had success with this- quoted below: "For a double kill switch you just need to make the circuit go to ground...

Ok, so I can generally figure out mechanical stuff, but I really struggle with electricity. I have the oil sensor removed from the inside of my clone, but never disconnected the external wire. I have a toggle switcht type kill switch mounted to my handlebars. I still have the original...

Trying to hook up a kill switch to my 5hp engine off a snowblower. I attached the new wire (red in picture) to where the old one came from. (White end of wire in other picture) Im spinning the engine with a drill but get spark reguardless if the new wire is grounded or not. Where am I...

I am at the end of an Azusa mibibike build.I need to mount the motor & install the clutch & chain and it will be ready to roll.On the front of my 5hp Tecumseh engine is a plug with a green & black wire going to it.What color wire do i hook the kill switch to?

How do you install a kill switch ? Right now I'm using a bent wire that pushes down on the spark plug on a B&S 2HP. I'd like to install a switch mounted on the handle bar. Thanks in advance. Tim

got a kill switch from bmi but no clamp came with it to mount to handlebar. i called them and was told i should use a conduit clip to hold it on. well that didnt work. i bought one from a local shop last year that is the same switch except it came with a two piece clamp. it is the toggle type...