shaft

Anybody have a 9 1/2 swing arm shaft in there stash. Its for my Bonanza MX rat for Windber. Looking for the original style with the clips on the end. Thanks everybody:thumbsup: OldMiniBikes is out of stock 9-1/2" SwingArm Shaft- Fits Bonanza Mid-Peg

im looking for a older h50 bigblock side cover (ball brg) one with a good governor shaft bore. p/n31451a thanks

Looking for drive gears, shaft, brake parts, and foot pegs (steel part not the cover) I have a rolling chassis, but sometime along the way the upper jack shaft, gears, and lower drive gears and bearings were lost. I am in Michigan, this is a project with my grand kids. Best regards, Jim...

I got a hell of a deal on a Flying"O" MTD with a HM80 3/4" shaft tiller engine with reverse shaft, the engine will power a Super Tyke roller I have. I need the jackshaft bracket and clutch if possible bit would take a bare bracket and build it up. I also need fenders and some cheap 12" eye to...

Looking for some help wondering what engine should go on this because i have seen Tecumseh 5hps and hodaka ace 100s but this version does not use a jack shaft so i need some help.

Hopefully this is a simple question. Im 90% finished rebuilding my 130000 series 5hp. I just realized my shaft 3/4" is about 1.25" long. I dont have enough to put a 2 sprocket clutch on it. Will a single sprocket work or do i need a longer crank shaft?

Not your typical mini bike motors but someone may have a use for them. 3.5 HP Briggs & Stratton vertical shaft engine I don't think it has ever been started, it is dirty and the gas tank and fan housing are dented. it also has the extra shaft coming out the side of the engine. 30.00 3...

I'm trying to find a overrunning sprag clutch sprocket to rework my trail horse jack shaft back to a two speed. I have the original jack shaft clutch & the 24 tooth freewheel sprocket, but the sprocket is missing rollers & springs. If anyone has any ideas were I can find a replacement sprocket...

Not sure of this motor. Looks to be a early h25 with a diaphragm carb. No exhaust. Has spark and compression. 5/8 shaft. No throttle controls on shroud. $45 plus shipping

Honda GVC190 vertical shaft engines for sale. My school's shop has 25 of these we need to sell off, will drive to deliver around N. Texas. Brand new, only a few test runs on most. Manual choke/throttle. ~27lbs each. Perfect replacement for most push mowers, or a creative bike application? $100 each

I'm looking for a Comet 20 series driver for a 3/4" shaft. Used is ok a long as it's in good condition.

Selling my Tecumseh HS50 that I bought a couple months ago. I was going to use this on my Gilson project but decided to go ahead and get the more correct H50 engine. It came off a lawn mulcher and ran great when I took the mulcher apart. The only thing missing is the gas tank and tank mounting...

Box of Parts Briggs exhaust - Briggs control panel - brake cable - briggs 3.5 head (damaged threads) - Bennelli horn & light switch - Harley pegs - hockey puck 3/4 bore - Tappered Generator shaft adapter - briggs exhaust deflector - briggs gaskets $ 75 + $10 shipping. no parting out - buy it...

Hey guys. Just picked up this little H30 side popper off eBay. It's got a keyed 5/8" shaft and a diaphragm carb on the long skinny intake. I want to retrofit this engine to make it minibike-compatible. I know I need the cable-type throttle control at the very least, but ideally I...

Hi, I have a Sears Roper in need of a running H50 with a 3/4" shaft. Any help would be appreciated. Thanks Doc

I upgraded a little bike from 80CC to 212 with a Predator ...with a 12 T clutch and 70/72 T rear sprocket...even with the extra horsepower I was having an issue starting out on hills with the stock gearing....SO... I added a jack shaft...based on recommendations I went from the 12T clutch to...

The sprocket isn't keyed, it uses a roll pin through the jack shaft assembly. 5/8" bore, 12T, #41 #15310 11 T SPROCKET FRONT,Standard 70 Roadster,Enduro, & Scrambler I'm really trying to avoid spending $25 on one if I can. Thanks!

i have this single cylinder diesel that i bought along with the two pallets of clone gas engines last summer. i will never use it and i would rather see someone do something with it: it does run, my engineer ran it when he was at the factory in china. i was told the engine was used as...

Apparently this is a bonanza scout mb250 that I have, and the steering shaft in the forks seem to have a little wobble in them. Feels worn out, and will also slightly bind when turning. I was wondering, does the shaft have bushings or something that can be replaced?

I'm looking for a K&S swing arm shaft. May have to have a machinist cut one to length and cut c-clamp grooves. The distance between the jackshaft plates is 7.5". I estimate that with c-clamps and washers, the shaft would need to be 8.5" long.