bend

  1. owend

    West Bend 61006

    Selling a 7hp West Bend motor. It was originally a chainsaw motor that I bought to use as a backup saw and I realized it's just too heavy to use. I ran it tonight without a problem and started on the third pull. Runs great, idles just a little high and will rev up without any problems. One of...
  2. Sunset5523

    West bend 820

    Trade for small mini bike missing bottom stuffer fan shroud and carb set up but have reed plate chrome bore looks good it can be run if u gather parts. Doesn't matter what kind of bike jus want it small thank you will send picture through phone don't know how to load sorry - Michael
  3. CarPlayLB

    Power Bee West Bend 820 820027

    Hello All, My neighbors do not appreciate the sound of an unmuffled ring-ding two stroke, so I am offering here....BUT WAIT! You guys are going to tell me I am outta my mind on price, before you do, please know I have well over $1200 into this! Here we go. This is the Power Bee labeled version...
  4. Mark G

    West Bend 580 crank shaft

    Looking for a good 3/4" crank for a WB580. I have cash or lots to trade....
  5. slywilliez

    WTB west bend 820

    I am looking for a complete or parts for the 820 west bend. Also I need an aluminum recoil for one all so. Thanks let me know what you have.
  6. E

    West bend ?

    Old west bent off my grandpas old go kart, would like info on it if anyone can help . Thanks.
  7. H

    West Bend Fuel Tank Mount

    Need one for a cylindrical tank going on a 580. Advice on fabrication one is also appreciated, since that's probably what I'll need to do. Thanks in advance. :thumbsup:
  8. Mac

    West Bend 580 Engine ? USED

    Old Two Cycle West Bend engine. The only numbers I see on it are 27126 on the killswitch sticker. Has a tapered shaft, good compression, and the exhaust mounting holes have been drilled and rethreaded to a 3/8" coarse thread. I don't see any spark, and I'm not about to hold the wire. :freakout...
  9. E

    west bend

    Could this be a west bend. Thanks. Joe
  10. boatguy

    West Bend 820 Clutch

    Looking for a West Bend 820 Clutch--10 tooth--#35 chain.
  11. Mac

    Fairbanks Morse, West Bend, ? , 2" Starter Cup

    Old starter cup for some kind of a Fairbanks Morse setup, or West Bend engine I guess. I have never seen the two "pegs" on the backside before on any others, and I have no idea what manufacturer made it. Looks like it was tried one time, and has a wear mark/scratch on the inside. $40.00...
  12. boatguy

    West,Bend,Bottom,Carb,Stuffer

    I am looking for a bottom carb stuffer plate for a West Bend 820 motor so I can move the carb from the top of engine to the bottom. Thanks Bill.
  13. N

    West bend 108 engine

    Hi gang, My name is Chip Quinn, and I have been a member here for about two years but have yet to post until today. I started building mini bikes and go karts here in Phoenix about 4 years ago, mostly with common Briggs engines that I have played with a bit since childhood, so I haven't...
  14. RokonDave

    PVL electronic ignition for West Bend 610s & 820s

    This is a new PVL electronic ignition mounted on a new production Wico points stator plate. This unit replaces the Wico coil, points and condenser on the older West Bend and Chrysler 820 CCW (PTO side) engines. Not drilled and tapped for the points and condensor. I have found it needs to be...
  15. hotrodricky

    West bend 820 identification

    Is there anyway to tell the model number and ccw or cw with the tags missing?
  16. hotrodricky

    West bend 820 identification

    Is there anyway to tell the model number and ccw or cw with the tags missing?
  17. CarPlayLB

    WTB West Bend 820 engine mount

    Hello, I just bought the Chrysler equivalent of the West Bend 820 and I need a motor mount. Please offer me what you have...even if broken! Eric at CarPlayLB@yahoo.com
  18. Jeff Clark

    Makin New Stuff..... West Bend Guard

    A new part I have been working on with some help from our local Bayareaburrito we have made a nice Guard for the West Bend 510 580 700 formed from the original tin one now the non existant will be available soon :thumbsup: shown is a polished part next to a out of mold part with the gates on it...
  19. S

    west bend 580 engine mount go kart cycle help

    i just picked up a west bend engine for my go kart cycle i was wondering if any body has a picture of engine mount location going from McCullough mc 49 to west bend 510 from a Lancaster chain saw model 400 i have a few ads from old kart mags but the engine is in the way model big bear...
  20. markus

    NOS Wes Bend 510 piston/rings

    NOS West Bend 510 piston/rings Bought the wrong parts awhile back. These are for a 510, cool old packaging:thumbsup: I know they say outboard, the numbers cross for any 510! $18 shipped
Top