bend

Can anyone show a picture of the throttle cable connection and connector hardware where it attaches to the engine? Thanks. Tom

Looking for a west bend 610 for a vintage kart. Let me know if you have one. Thanks

I just picked up a 580 that has a Caruso or maybe capuso centered intake/stuffer on it. Kinda looks like a go power from what I have seen, not sure what the reed plate is I am guessing maybe Gem (if It is can I get new reeds for it :shrug:) Anyone ever heard of it, and whats it gonna do for...

Looking for a west bend 820, CCW rotation while looking at the pto side. Will consider all conditions

Used WB 820. CW rotation (looking at the PTO). This came off of a Sno Runner so it has a light coil. Stepped crankshaft, I believe it's 9/16" down to 5/8". Tillotson HL320A Carb. Carb is nice and clean, not gummed up but I'm sure it would need at least a gasket kit and a good cleaning. Bore...

Here is the correct West Bend tank and mount..:thumbsup: Vintage Kart Gas Tank for A West Bend 700 580 510 with Original West Bend Mount | eBay

I am looking for a west bend air cleaner like the one posted for a Arctic Cat screamer project. I have found out that Gem made some air cleaners just like this one but the end cap was just blank. I need up to five of this filters and end caps. I have the bases and the two hold downs. Thanks...

Here is a chromed out gem of an early 60's West Bend air cleaner. I had this patiently chrome plated to the brilliant luster my bad photos cannot possibly capture! This has the inner screen that is not plated, the original bolts, and I will toss in a new gasket. Boys and girls, the shiny ain't...

Been wanting one of these for a while now, Its a little dirty and I haven't heard It run yet....but that's OK it does turn over and has good compression. My good friend and brother by another mother Eric (CarPlay) is sending me a gasket set so that I can clean it up and check It out. No suped...

Looking for a open header, custom type for a West Bend 580 engine. What do you have ? Thanks in advance, ond.

Hi, got a Baja MB200 from tractor supply. Got a performance kit from hotrodminibike. The header is rubbing the frame. They should have had the header bend a little farther out...like even 1/4" would be fine. As it is, I can't tighten both nuts on exhaust flange down onto the engine head...

Picked led this up today. Anyone know what model WB?

Just ran across this nice motor built by Frank Moore Vintage Go Kart Mini Bike West Bend Power Bee 580 Dual Carburetors | eBay

Cool little bike on CL https://detroit.craigslist.org/okl/mcy/5177607064.html

I recently got a West Bend 820 built by Frank Moore of Ohio. He does a fantastic job at reasonable prices and really knows these engines no matter what model. He can rebuild yours or he has a supply of engines/parts, like the one he sold me, to complete your project. Frank can be reached at...

WTB early West Bend 820 Engine ID Plate that is held on by two small screws to the flywheel air shroud. If you have one let me know and calling me is the best way to reach me. Mike Cates, CA. (760) 473-6201

I am having a West Bend engine rebuilt / restored and wanted to know what the engine should look like for use on a 1964 Taco with Hot Sauce. Does someone have a log of serial numbers of the engine to determines it's year of manufacture and what color should it be? I have seen the 820 fully...

WANTED THESE ORIGINAL PARTS FOR A 1964 TACO FITTED WITH A HANGING WEST BEND 580 5 PORT ENGINE: 1) Short 4" round x 7" long gas tank. 2) Chain guard that covers PTO clutch sprocket to jackshaft sprocket. 3) Hand brake lever. 4) Air filter with single screw OR double clip type for WB 580 5...

Looking for a Taco series 1, 55 or 99 with hanging engine. Prefer the 99 with West Bend 820 but let me know what you have. Serious buyer. (760) 473-6201

i would like to buy a savage mini bike with west bend engine anything and everything message me or call me 513-602-5089 minibike todd got a lot of bikes i can trade on too like herald super bronc and others