bend

This was on a West Bend 580 I had. What is it called? Thanks

Here is used Reed West Bend muffler. This is a repop from Vince Hughes. Pay Pal gift payment only please. $45.00 plus shipping

4" manco wheels $100+shipping One of the halfs has a bend on it. Another set of wheels $40.00+shipping I think this one is a 6" wheel not sure(will update later) tire has dry rot $25+Shipping

Does anyone have the seal numbers, Pto & Ign. plate for the West Bend 580

got an old west bend 510, believe its 1959, very similar to 580, good compression, needs plug wire 150 plus ship

Vintage ORIGINAL West Bend cast aluminum mount for 610 and 820 engines. Includes the steel upright mount which allows you to clock the motor every 22.5*..the slots also allow for height and pitch adjustment. Not to be confused with the reproduction stuff... Getting very hard to find these...

Here is a West Bend engine for 580 or 700 models. $20.00 plus shipping

looking for the cylinder head cover for 820 west bend with angle plug, want one with no damage, thanks

nos roper front fender, I bought 2 from a guy here hoping I could use it on rear, but no way I paid 60 want close to that 580 west bend motor mount, metal 25.00 nos 820 west bend recoil 75.00 tec hs 50 white, good compression 150 pics coming

Does anybody have any software for a JD32 bender? My buddy bought one and then JD2 removed the software they had up on there website. He contacted them and they said they are working with Bend Tech to come up with some software but the Bend Tech software is like $400 plus. I know people on here...

I just recently scored a west bend 820 with slanted spark plug for climbing under a guys car and replacing a leaky transmission valve. he claimed it was used on a boat and has a strange thick steel L shaped mount on the bottom, maybe to bolt to a transom with chain drive to a propeller? i...

unknown if runs,has great compression,showing 90lbs. what you see is what you get,engines are complete minus exhausts. these were all surplus from a heavy equipment operator who bought them from Stone company. they were in a tractor trailer,gathering dust for many years. they dont look like...

Vintage collectible 1959 West Bend 580. Strong compression/good running. HL134A carburetor and Go Power intake produces 5-1/2 to 6 HP. Needle bearings on the wrist pin and crank pin, ball bearings on the crankshaft. Clutch/mount included. Good motor for a mini bike or go kart. $450 + ship from 49279

New block,piston,bearings, seals, gaskets,motor-mount,ready to mount,add clutch and go. $450.00 OBO regards,Joel

Has good compression. Anyone near Michigan work on these motors? I have the recoil but it needs repair. Is this a late 60's motor? What driven works with this driver clutch?

looking for a used engine plate we can mount and use for a test stand to get a bunch of motors running. im assuming? this is the plate i need? also,if anyone has any tips for going thru these 2 cycles and starting them up/some for the first time,please lmk. thanks. Vintage Go Kart Motor...

I need an exhaust pipe that may not be doable. I need a 6.5 HP Predator pipe to bend 160-180 degrees. The pipe needs to bend as soon as it leaves the engine and not go out more than 1.5 inches. I would need the flange and at least 6 " of pipe to mount the muffler. Is this even possible? Who can...

I need West Bend 820 LH Threaded Nut for clutch side of crank. Its about 1" long and holds the clutch on. Needed for Trapper Mini Bike build. Thanks Frankster

Did some work on the 580 today and luckily it started second pull. I need a clutch and the crank is 1/2inch. Is this normal and where could I get a clutch? Thanks.

Looking for gas tank brackets that mount the tank to the engine on a West Bend 580 motor. Appreciate any help.