greyhound

Need this gas tank for my greyhound build. Anyone ?

Here is the latest phase of my Monster Frijole. It has a 79cc Greyhound with a race carb from AGK,an open header,and a homemade hoopty air cleaner made from a spray bomb lid. I solved the fuel tank problem by simply using a motorized bicycle tank,which was under $40.00 in chrome. Obviously you...

Hey Folks, My 2.5 greyhound on my daughters arco has an intermittent thing where you turn off the motor with the gas supply petcock on, and gas leaks out from somewhere near or from the carburetor :shrug: ? It's done this twice now in the past couple weeks, so I am going to take the...

Hey guys basically the title says it all. Im buying a predator to swap my greyhound but im wondering if the bolts i drilled will line up with the new engine. I know there both Honda clones but im not sure if the mounting point is the same. Let me know.: scooter:

so i finally got the engine rigged up on the doodlebug frame i have, and yesterday i replaced the old fuel line with a really thick fuel line i found on an old engine. now, when i start it, first of all it is pulling itself forward ( im guessing the idle is too high, but i dont know what screw...

I recently posted about a 5.5hp side cover, bought one and it didn't fit. talked to the seller and he determined I need a HF Blue Lifan (Greyhound) 5.5hp side cover. The side cover will come from this motor which has a 5 bolt valve cover like mine. If you think you have what I'm looking for...

Well I'm a little new to the minibike scene but I've worked with other things that run on small engines (i.e. generators, lawn mowers, lawn tractors) and thought this would be cool to get going again to have something fun to mess around on until I decide to ride a motorcycle. Of course I'm only...

6.5 Greyhound, upgraded billet rod/flywheel, governor removed, needs throttle hook-up {some parts missing} and the pulley is stuck on the shaft. Runs GREAT. $175.00 plus exact shipping.

I have a Greyhound 79cc clone that had a broken recoil-so I got one from a 99cc Predator. It bolted right on,and looked exactly the same-but when I pulled the rope,it made a grinding noise and did not engage the flywheel. But I am able to start it if I hold the recoil away from the flywheel a...

Here is the Taco so far......I removed the 79cc Greyhound from my Orange Sprite to see if it would fit. As you can see,it JUST fits. The mounting plate will need additional holes drilled,and a header will be needed,but it will work. This little engine has a surprisingly good amount of power,and...

My faithfull Greyhound starts fine and runs great for about a minute and then stops dead. It starts right back up on usually the first pull and then quits again after about a minute. What should I check and how? Thanks for your expert advise!

I advanced the timing 8 degrees with a new timing key, i put on a straight header/ muffler, i put on a airflow adapter with a k and N air filter, New spark plug and a new carb from NR racing. The carb i got was the honda one bored out to .625 with a 95 jet. Once i got it together when i could...

I recently got a 2.5 hp Greyhound engine that did not include the steel mounting plate bolted underneath the engine. Does anyone out there have one? Thanks for any reply.

I have a 6.5 hp greyhound motor that i replaced the exhaust with a straight back header, well since doing that i can only run a half choke, any more and it will bog out. I know its considered a "clone". I know i need a new airfilter, the adapter thing and a choke bracket, will these 3 parts work...

I just got a 79cc Greyhound 2.5 hp engine cheap-apparently,the carb needs cleaned. Anyone out there have an exploded diagram of one of these carbs? Question#2-I noticed that AGK has a performance carb for the 79cc-99cc Predator engines. If I install one,what else would I need to get the most...

I am in need of cleaing it and doing an oil change so i have a few questions, A) has anyone used this stuff if so how easy was it and did it work good. Buy Solder Seal/Gunk Engine Brite® Heavy-Duty Engine Degreaser (15 oz.) EB1 at Advance Auto Parts B) on a Greyhound 6.5hp motor what oil...

Tried a Predator Assembly but doesn't work, need one that has flat, not round pins. Thanks Mike

Hi, I replaced my starter assembly and all I could find thru Harbor Freight is the one for the Predator, which has the same 3 hole pattern, but it doesn't work right. The 2 pins on the assembly are round and not square so it won't engage correctly. So I need either a Greyhound starter...

Hi, Had a little mishap, Airbox for Greyhound 196cc Motor broke... Anyone know if the Predator 212cc AirBox will work ? Thanks Mike

Ok, I picked up this minibike with what looks like a hardly run greyhound on it. Everything on this bike has been rigged up and is taking a lot of undoing. Today I messed with the motor for the first time and got it fired up but it is spitting all kinds of black smoke. The thing that really...