Got a bit of pretty stuff for my build...ebay (like $40 bones)of course,,,,Chrome oil catch with top breather ......I know its overkill but it fills the void in the frame in front...
Had to make my own brackets and it will be hooked up to intake and valve cover for venting..
How On earth do I install These spring retainers and keepers? I see how the retainers work, but the keepers have me stumped. I'm using my phone or else id do a search. Any thread someone can link me too? Thanks a bunch.
Hi All
I am installing the chain on my Fox minibikie for the first time. It is a new engine (HF212cc) and clutch. There is no chain tensioner. Direct connect from the clutch to the rear sprocket. The only adjustment is the slotted holes in the engine mounting plate.
I read here I need 1/2" to...
Can someone give me a step to step on installing my 22mm mikuni carb on my predator 212 the bolts to hood the carb to the engine seem to be too long..how can i take the bolts off..also what size bolts should i run ?
Whats the trick to compressing the spring to install the split keepers..? Also is it normal for the inner spring to ride on the head that supports the valve guide vs down in the spring pocket like a normal spring....
Newbie - here with a question on isntalling a Max Tor clutch which I could not answer by using the search button. When installing a Max TTor clutch on the 6.5 HF engine are shim washers used on the crank side ? Pro Mod send 2 shim washers but they don't take up all the clearence on that side ...
Hello all, new to this site, there are some talented people on here for sure...I have a Baja warrior and am VERY interested in putting a torque converter on it..Based on some tutorials I saw on Youtube, it doesn't look all that difficult. I am average to slightly above average as to my...
I started out with a bare motor plate:
MOTOR PREP.
1. Remove the spark plug wire so it won't get broken while you are trying to line up the motor.
2. Remove the air cleaner cover.
3. Remove the exhaust pipe.
Hey everyone.
I have two jackshaft kits coming for my girls minibikes. I got the clutch off with out tomuch trouble but it is hard to hold the shaft from turning to get the bolt loose.
Is their any trick to holding the shaft so it won't turn?
It was not to bad to get off but...
I fought the sissy bar and I think I won?
For those who know how hard it is to find original parts like sissy bars, clutch chain covers, etc. Sometimes you have to improvise and "make your own" out of something else. Well I purchased a sissy bar off of ebay that probably came off of a...
I just got my arc billet rod, flat top piston, and fly wheel. I assembled the rod and piston and tried to install it. The rod hits the cylinder/ block. I thought I put the rod on wrong so I turned the rod around on the pistonput it back in now the oil slinger hits the cam what am I doing wrong?
Was looking for advice as if you have to do any major modifications to the engine to install a tav2 or if it is direct bolt up. I have searched many different places including here and couldn't really ever find a clear answer. I also looked into the TC2 kit that said no mods needed but wasn't...
Can anyone assist with a picture of how the spring is installed on the old school DB30 footpegs? I removed mine months ago before I stripped the frame and failed to note how it goes together. I fumbled with it last night and could not sort out how the spring is attached to the frame and peg...
I am trying to figure out how to put a rear disk brake on my latest project. I searched pretty good, and could not find much information as far as 'how to'. The biggest challenge seems to be how to mount a disk on the right side. Any suggestions? Thanks.
Picked up a clutch brake kit for my Boonie. The instructions are horrible. They are actually just an exploded view of the assembly. The mounting bracket does not appear to fit the case. Do I have some obsolete engine? The kit says it fits briggs, tecumseh, etc... Engines with a 4 bolt flange...
How do i install this kill switch to this engine?
http://img812.imageshack.us/img812/7482/photomz.jpg
http://img843.imageshack.us/img843/7066/photo2hay.jpg
ok here we do a install and oiling of a max torque clutch .this will be how to mount one using the set screws .
ok check that the key fits in the slot on the crank and the clutch.
use a small rat tail file to remove any burs , or rust in the slot . the key should slide nice free no binding ...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.