sleeve

I'm looking for a brake cable adjusting sleeve for drum brakes like the picture below. I know I can buy them at various places but where can I get one without paying a lot for shipping? a lot of places want $7 to ship a tiny thing like this. Heck it probably only sells for $3... Any...

Some Minibikes have a nylon bushing sleeve inside the bigger diameter tube for the smaller diameter tube to slide in. A lot do have any bushings. It is just one steel tube sliding in another steel tube. Those are sloppy fits. It is most likely a 7/8" tube inside a 1" tube. Who sells the nylon...

Picked up a pretty cool '67 H50 Tecumeh and it had this pretty cool starter that uses the PTO and a sprocket rather than the flywheel. I dont know what i'll do with it but for now I just want it off. And off it came. But this sleeve wont come off until I get this pin out. It goes all...

How far is too far too bore my i/c motor. .150 piston would bore the sleeve out but would .120 be cool?

I have a Genuine Honda GX200 and I would like to do a 3in build. can someone tell me what are some of the challenges I will have with the build as far as having it resleeved? like when you resleeve the block do you have to leave the sleeve raised above the block and cut the head to except the...

Hi I'm looking for a Briggs cast iron sleeve 3.5 I got stuff to trade. I only need the block. Thank you.

Does anyone know of, or make a reducer sleeve? Want to use a 3/4 bore clutch on a 5/8 shaft engine. Thinking on building a motorized bicycle with a 3hp Tecumseh, and use a Downs brother manuel clutch.

Hi guys, I need help figuring out a briggs type number. The complete number is 204412-0156e2-0505xxxx, I know the meaning of the first part but not the type number. I ask because I have two engines with the same model number as this one and they have different covers but mainly I want to know...

Who knows the deal with this silver sleeve on the output? Is it removable? Will it slide off? Does it need to stay on? It doesn't just fall off, I don't want to screw it up. Thanks

Hello, I recently started restoring a B&S motor. Thanks to your site I was finally able to figure it to be a 4hp (10 stamped on head) Kool Bore. After pulling it apart and looking it over, their was at least 1 score in the cylinder deep enough to warrant a aggressive hone if not re-bored. So...

Looking for a header sleeve like the one in this pic Any ideas where to buy one?

Pulled my side cover off to get to cam. What is that sleeve and where can i find a new one??:shrug::thumbsup:

Here is my method for changing bearings. I am sure some will do things differently, but this has worked for me with simple tools. If you do not feel confident in what is shown and described, please do not attempt. I had to say that, but there is nothing hard about it (most of the time)...

Can anyone tell me where I can purchase a 3/4" to 5/8" keyed sleeve reducer for a driven unit?

Can you replace the cylinder sleeve and what is the max ID you can run?

I am seeking advice, having never attempted to build an engine for performance before. I have rebuilt my 5hp briggs in the past but its time for another go around. This time I want to aim for "bang for buck" performance as the engine is going back on an old go-kart. Last night, when I took...

Anyone know where I can get a bushing or sleeve to use on a 3/4" shaft to bring it up to an inch? I can't seem to find one. I actually want to use a spare motor on a leaf blower that requires a 1" shaft.

i need a 5 hp briggs motor w/ cast cylinder sleeve also with the newer intake flange, i will be running a tillotson carb with an ec manifold. i will post a pic of what type of motor i am talking about.

Does anyone have of those, if so please emaikl me with pics happydingdong@live.com