governer

i took a brand new out of the box 212 cc prediter engine and put the honda clone electrodes and flywheel on it. i ran the cord safely behind a heat sheild that i ground down slighly to accomodate it. the nut on the crankshaft goes halfway on (litterally half of the nuts threads are used) i used...

I'm getting my billet parts in about 1-2 weeks... I wanted to remover the governer but didn't want to take out the whole linkage... I can just take the little plastic gear out correct?

Ok so I recently got the 212 and put it on my mini bike. Now when I got it where the throttle hook up is suppose to go which is on the governor throttle I put it but it was super stiff. So I eliminated the governor throttle and ran my throttle cable to the little swing arm thing under the gas...

So ive been doing alot of motor work before the engine goes onto the gokart frame.. ive been sanding / grinding / welding alot on the frame too.. Ive ran into a few questions thought. Like how the hell you hook rear brakes up?! My left pedal has a metal line running from the pedal to the bak...

what i believe to be a h5k series motor. Can I disable the governor? It seems as though i cant get proper thotthle return with it intakect.:shrug:

Anyone have a spare governer spring that goes between the lower tank brace/throttle plate to the gov arm?.....Or a linky? Thanks Trade/paypal Jim

I'm getting ready to hook up the throttle on my old 2-1/2 horse Tecumseh.The return spring on the bell crank is broken,but I can get around that.What I need to know is the position the governor arm and throttle is supposed to be in at rest.I know on some things the throttle is wide open until...

I have two used Baja MB165's that I'm bringing back to life. One of them looks to have the correct throttle/governer setup and the other has been messed with - missing springs. I called the parts department at Baja who says all their springs are on back order until December. Are these...

Anyone have a GX200 governer spring you don't need? On the Greyhound engines it's the black spring. Thanks

Hello, I'm having problems with the Greyhound engine I have surging. I'm wondering if it's because the black spring on the governor is too loose. If that is really loose, would it make the RPM lower? Because there's a ton of play in it. Should I bend it so that it's not loose?

I am having trouble getting the governer linkage back on to the shaft that comes out of the case. The shaft pushes back into the case and makes it very hard to get the linkage back on. I must be overlooking something, any advice? Here is a picture. Also when putting the linkage on should the...

ok - i guess ive been confused all along. when i got my 6.5, i took off the bulky lever assembly under the gas tank , which i thought was the governer. so i did the same to the mb165. it had a lever assembly thing that was stopping how much throttle you can have. is this not the...

I Ripped this off of DIY Go karts because I thought it would be a good contribution to this forum. CREDITS TO SOLOMON FROM DIYGOKARTS FOR WRITING THIS THREAD. __________________________________________________________ WARNING-DAMAGE CAN OCCUR TO YOU AND ENGINE BY DOING THIS MOD Okay, I...

I Ripped this off of DIY Go karts because I thought it would be a good contribution to this forum. CREDITS TO SOLOMON FROM DIYGOKARTS FOR WRITING THIS THREAD. WARNING-DAMAGE CAN OCCUR TO YOU AND ENGINE BY DOING THIS MOD Okay, I have made a STEP by STEP tutorial for removing the governor on...

Not on a minibike... But I'm sure somebody might be able to use the pics in the future: Trying to get an H70 130210E engine going for our snowblower. Pictured below is the carb/throttle/governer linkage setup as it was before I took it apart. My biggest question....is the linkage connected to...

I am about to remove my 2nd HF clone governer. The 1st one I did went fine but it was a :censure: getting the plastic gear out, because of the split ring keeper, of course. So, what is the hot tip on getting them out?? :hammer: a bigger hammer, perhaps??.

It felt like I lost top end speed a little bit. I had more torque. There is a hill I climbed with governor on and I had to stop and walk the bike up. Today with governor off, the same hill, I sat on the bike and took my feet to give it a boost but made it without getting off the bike...

All right guys, I just picked up an old briggs 5hp flathead. I took off all the existing linkage on it, which looked like it was for a tilller. Right now I have my new linkage setup going directly to the butterfly on the carb. My question is, do I have to hook the governor up to my new linkage ?

My kids have a new db30 and they already want it to go faster! I am looking into the 6.5 clones at harbor freight but until then i would like to know a few tricks to make the stock 2.5 a little faster! Please refer me to any links or discussions on making this model a little faster.It will be a...

My kids have a new db30 and they already want it to go faster! I am looking into the 6.5 clones at harbor freight but until then i would like to know a few tricks to make the stock 2.5 a little faster! Please refer me to any links or discussions on making this model a little faster.It will be a...