handle

It's a long shot......but I need handle bars for a quarterhorse as well as a muffler. The muffler can be for a Mac or a WB 610/820 since I haven't decided for sure which engine I'm going to use. Thanks !!

If it has the opportunity to receive one answer point someone will jump all over it right? :laugh: Guy on Evilbay asked what the dimensions of the handle bars are.. That would require me going back and measuring them.. :laugh: anyone know what the dimensions of a Roadster II handle bars...

Something just ain't adding up you be the judge.:shrug: RUPP MINIBIKE, VINTAGE RUPP MINI BIKE, 1969 HANDLEBARS: eBay Motors (item 220696567483 end time Nov-14-10 15:12:41 PST)

I ran across this cool old pull handle, I believe it may be off of an old chainsaw. I put it on one of my old Fairbanks Morse recoil units, appears like it belongs there.

Hey guys Im looking for some stock handle bars for a Huskee Hill Climber. Preferrably good chrome The ones I have need replated and I thought I would try to find a used set . I figure they maybe cheaper than replating mine. I'll post a pic with dimensions tomorrow.

i just got another project bike. I`m not comfortable with the handlebars straight back, i`d like them to lean forward abit. is there a common way to accomplish that and have it look proper?

bars are in perfect condition. asking $25 and $40 shipped to lower 48. located in so cal.

$40 shipped. Mechanicsburg PA Cat Bars. Not bent or repaired. Need refinished. Someone spot welded them to the forks. That area will need ground and polished. Rear Hub. Should Be blasted.

I'm in need of the bars to fit a 400x. No cracks or breaks.

wanted 7/8 handle bars risers aluminum.

I have a set of used Rupp shocks , they are in fair shape , little rust on springs but show no signs of leaking , tHe bushings are missing , Two sets of Handle bars off I dont know what ,, 20.00 on the shocks plus shipping and 10.00 on the Renthal pad ones 20.00 on the extended higher ones ,,

I'm new to mini bikes. I'm trying to restore a Keystone, I think. See: what is it. I have searched the internet for handle grips and foot peg rubber. Can anyone help me out with a few web sites or phone numbers of dealers. Any leads will do. I have looked at a lot of the cool rides on this...

is there a specific handle size for a throttle handle on the db30? mine got all ripped up when my dads friend crashed my bike

i was looking at some on ebay for a while and i just missed some. so im giving up and seeing if anyone here has some. i need those ones that are 2 seperate pieces and they bolt into the crown and they fold down as well.

Hi All, I am in need of a complete brake handle assembly that will fit 1-inch O.D. handle bars. Needs to be for the left side. Thanks, Mike

I am trying to locate a complete brake handle assembly (left side) that will fit 1-inch O.D. handle bars. I have done a bit of searching online at the mini bike parts suppliers and only have find 7/8-inch assemblies. Any ideas? Thanks, Mike Laharview Farm

I just got one of these. Looking to upgrade from the 5 hp briggs. Im on my 3rd 5hp briggs on the same bike with in 2 years. I just want to know can this motor handle higher rpms good? Im worried about throwin a rod at about 5,000 rpm Its a tehcumseh 5.5 hp

any one out there with a set of cat 400x handle bars and seat!!!!! thease are the only things i need to finish the original bike call 831 297 0007 thanx:biggrin:

I just got a Murray minibike today and was out in the garage messing with the handle bars, I have 2 type of taller handle bars I tried out on it. I not sure which set I like better, I leaning towards the taller ones and my wife likes the Rupp ones better. Here's some pics and see what you think...

I just purchased a mini bike but the handlebars are bent. Does any body have any for a hawg-ty